Switch to accessible version
BOSS

BE600.2D

$159.99

add to cart
  add to list

ELITE 600 Watts, MINI Class D 2 Channel Power Amplifier, Remote
Subwoofer Level Control

Elite MODEL 600W High Output 2 Channel Full Range, Class D Amplifier Dim:9.7"L 4.6"W 1.7"H

  • MODEL 600W High Output 2 Channel Amplifier
    Up to 225 W X 2 RMS @ 2 ohm
    Up to 113 W X 2 RMS @ 4 ohm
    Up to 450 W X 1 RMS Bridged @ 4 ohm
  • Full Range, Class D, MOSFET Power Supply
  • High and Low Level Inputs,
  • Variable High Pass Crossover, Variable Low Pass Crossover, Variable Bass Boost
  • Illuminated End Panel Strips 5 Years Elite Warranty
  • Dimensions: 9.7" L x 4.6" W x 1.7" H

 

KEY FEATURES:

2 Ohm Stable

The lowest impedance accepted by this amplifier is 2 ohms. Amplifiers that are 2 ohms stable produce more power resulting in more volume. This amp can comfortably power speakers or subwoofers with all channel(s) being used at a load of 2 ohms.

Bridgeable

Bridging an amplifier means to combine channels of a multi-channel amplifier to get more power or flexibility out of it. For instance, on a 4 channel amp, channels 1 and 2 could be used normally for your speakers, and channels 3 and 4 can be bridged for more power to a single subwoofer. A 2 channel amp can also be bridged to power a single subwoofer.

Class D Amps

Class D is a high speed switching amplifier technology that is more efficient, generates less heat and draws less power than traditional Class A/B amps. We use Class D in our monoblock amplifiers to give you massive amounts of power in a relatively small footprint for clean, powerful, bass.

High and Low Level Inputs

An amplifier with both high-level and low-level inputs provides flexibility by allowing you to build an audio system using virtually any standard factory or aftermarket source unit. High-level (speaker level) inputs accept the signal from the speakers, while low-level (RCA) inputs accept the signal from the pre-amp outputs of the source unit.

Illuminated End Panel Strips

The end panels of this Rage Series amp has Blue Illuminated light strips that glow when the amp is turned on.

Protection

If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself.

Switchable Input Sensitivity

Switchable Input Sensitivity gives you the freedom to connect the amp to any standard source unit and have peace of mind it will be within range to properly match the output of the source unit allowing you to use the volume controls on your source unit the way it was designed.

Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Variable High Pass Filter

Variable high-pass filter gives you control over the frequencies that pass through to the full range speakers.

General Specs

CHANNEL CONFIGURATION

2/1 Channel

POWER SUPPLY TYPE

MOSFET Power Supply

AMP TOPOLOGY

Full Range, Class D

Performance Specs

TOTAL POWER OUTPUT

600 Watts

PEAK POWER @ 2 Ω

300 Watts x 2

PEAK POWER @ 4 Ω

150 Watts x 2

BRIDGED POWER @ 4 Ω

600 Watts x 1

RMS POWER @ 2 Ω

225 Watts x 2

BRIDGED RMS POWER @ 4 Ω

450 Watts x 1

RMS POWER @ 4 Ω

113 Watts x 2

SPEAKER IMPEDANCE

2 to 8 Ω

T.H.D. (TOTAL HARMONIC DISTORTION)

0.010000000000000000208 %

CHANNEL SEPARATION ≥

90 dB

S/N RATIO (A-WEIGHTED)

103 dB

FREQUENCY RESPONSE

9 Hz to 50 kHz ±1 dB

Connections, Controls, and Processing

RCA INPUTS

2 Channel

HIGH LEVEL INPUTS

LOW PASS FILTER

50 Hz to 250 Hz

HIGH-PASS FILTER

Variable 50 Hz Hz to 250 Hz

BASS BOOST

Variable 0 to 12 dB

INPUT SENSITIVITY SWITCH

THERMAL/OVERLOAD/SHORT PROTECTION

Measurement

WIDTH

4.5999999999999996447"

HEIGHT

1.6999999999999999556"

LENGTH

9.6999999999999992895"